Allen-sports 645RR Manuel d'utilisateur télécharger pdf

Model 645RR Instructions

English - Page 1

WARNING: Bikes or rack falling in road can cause serious accidents resulting in bodily injury—do not use rack on

any vehicle on which it can not be properly mounted as described in this instruction sheet.

• Rack should only be used on vehicles with 2” receiver hitches.

• NEVER use on trailers or front of vehicles.

• Bikes must be tied to rack using tie-downs, or additional straps if necessary.

• Check periodically during use that all bolts and pins are tight, and that rack and bicycles are secure.

• Never carry more than 4 bikes (max capacity 140 LB) - no tandems, mopeds, or recumbents. Car tail lights must

remain visible.

• Drive conservatively, especially over bumps. Never use off-road.

• Do not use if any part of the rack is damaged, worn, or missing. Contact R. A. Allen Co., Inc. for replacement parts.

CAUTION: Use Allen 645RR only in accordance with local motor

vehicle and traffic regulations.

• Install rack and load bicycles only at a safe distance away

from moving traffic.

• Make sure that all of rack and bicycles are kept at a safe dis-

tance from road and hot exhaust.

• Only operate vehicle with rack in an upright, locked position.

• Bicycles should never extend beyond sides of vehicle.

• Remove rack from car, or fold carry arms down when not in

use.

PARTS:

TOOLS REQUIRED: 2—9/16” WRENCH & 2—3/4” WRENCH;

OR 2—ADJUSTABLE WRENCHES

645RR B

OX SHOULD CONTAIN THE

FOLLOWING ITEMS:

1—H

ITCH INSERT 1—CARRY ARM

SSEMBLY

1—RR P

OST

1—HARDWARE KIT,

CONTAINING

2—3/8” X 2 1/2” BOLT

1—3/8”

X 3” BOLT

3—3/8” L

OCK NUT

1—1/2” L

OCK NUT

1—1/2” N

O-WOBBLE

OLT

ASSEMBLING RACK:

STEP 1

STEP 2

HITCH INSERT

RR POST

3/8” LOCK

3/8” X 3”

OLT

•INSERT CARRY ARM

SSEMBLY INTO UPPER

PORTION OF RR POST,

LINING UP THE HOLES

IN EACH PART.

•INSERT THE 3/8” X 2

1/2”

BOLTS THROUGH

EACH HOLE, AND

THREAD 1—3/8” LOCK

NUT ONTO THE END OF

THE BOLTS.

•TIGHTEN NUT AND

BOLT FIRMLY USING

TWO WRENCHES.

NOTE:

UPON COMPLE-

TION

, BOTH PARTS

SHOULD BE FIRMLY

JOINED TOGETHER.

CARRY ARM ASSEMBLY

3/8” X 3”

BOLT

QR CLIP

IMPORTANT:

WHEN RACK IS IN AN

UPRIGHT POSITION,

IRE RETAINER ON QR

LIP SHOULD ALWAYS BE

IN A CLOSED POSITION

TO KEEP RACK FROM

FALLING OVER DURING

USE.

1—70” BOTTOM STRAP

•INSERT LOWER PORTION OF RR POST INTO

ITCH INSERT SO THAT THE HOLES AT THE BOT-

TOM

OF EACH PART LINE UP.

•INSERT THE 3/8” X 3” BOLT THROUGH THE

HOLE, AND THREAD 1—3/8” LOCK NUT ONTO

THE END OF THE BOLT.

•PIVOT THE RR POST INTO THE UPRIGHT POSI-

TION, SO THAT THE POP-UP PIN SNAPS INTO

PLACE. INSERT THE QR CLIP THROUGH THE

HOLES, AND SECURE THE WIRE RETAINER CLIP.

•TIGHTEN NUT AND BOLT FIRMLY USING TWO

WRENCHES.

1 2

Résumé du contenu

Page 1 - ASSEMBLING RACK:

Model 645RR Instructions English - Page 1 WARNING: Bikes or rack falling in road can cause serious accidents resulting in bodily injury—do not use rac

Page 2 - SECURING BIKES TO RACK:

Model 645RR Instructions English - Page 2 C. INSTALLING RACK ONTO VEHICLE: •WITH ARMS IN FOLDED POSITION, INSERT RACK INTO RECEIVER HITCH. LINE UP HO

Commentaires sur ces manuels

Pas de commentaire

Allen-sports 645RR Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour les vélos Allen-sports 645RR. Allen Sports 645RR User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour les vélos Allen-sports 645RR